(sold)Pre-owned DJI Ronin-M Kit

Add Your Review

Stock Status

SKU: 04H0031143
Categories: Ronin, Pre-owned



Condition: 7/10 = Shows signs of use but very clean.

A copy of your ID Document or Drivers Licence is required to purchase this item.

Winner of the 2015 Videomaker award for best camera stabiliser at NAB, the Ronin-M weighs about half the weight of the original Ronin thanks to its magnesium-built body. This lightweight electronic gimbal is designed for DSLR and smaller rigs, supporting cameras of up to 3.6kg (8 lb).


Quick and Quiet

This Ronin-M can be auto-balanced at the press of a button through its DJI Auto Tune Stability (ATS) technology. The unique SmoothTrack Control will make sure your camera faces the correct direction – regardless of abrupt angle changes. The side handles can be removed to put this Ronin-M into a very compact briefcase-mode while Silent Mode quietens the motors and allows you to shoot with minimal distractions. In addition, a dedicated power box is available for connected accessories.

It can be held in the same three positions as the Ronin and is mountable onto other rigs, tripods, cranes and jibs using a quick-release system. This Ronin-M comes with the Thumb Controller but offers support for an additional operator and is customisable using the DJI Assistant smartphone app.

Because of its lighter weight and payload, the Ronin-M’s smart battery gives you over 6 hours of runtime. So get running with this Ronin-M today and capture smooth cinematic shots for your next creation.


Shooting with the Ronin-M


Ronin-M Balancing


Ronin-M Tuning the App

Load Weight (Reference Value) 8 lb / 3.6 kg
Angular Vibration Range ±0.02°
Maximum Controlled Rotation Speed Pan Axis: 90°/s
Tilt Axis: 100°/s
Roll Axis: 30°/s
Mechanical Endpoint Range Pan Axis Control: 360°/s
Tilt Axis Control: +105° /-165°/s
Roll Axis Control: ± 110°/s
Controlled Rotation Range Pan Axis Control: 360°/s
Tilt Axis Control: +105° /-165°/s
Roll Axis Control: ± 25°/s


Motor Type 3 x Brushless
Working Current Static Current: 300 mA (at 16 VDC)
Dynamic Current: 600 mA (at 16 VDC)
Locked Motor Current: 10 A maximum (at 16 VDC)
Sensors Independent IMU module
Temperature sensor

32-bit DSP processor


Frequency 2.4 GHz
Expandability D-Bus receiver supported


Wireless 2.4 GHz for transmitter (remote controller)
Bluetooth 4.0
Wired 2 x 12 VDC regulated PowerTap 
1 x USB power output (500 mW) 
1 x DJI Lightbridge interface


Assistant Software Desktop: Windows (32- or 64-bit): 8, 7, XP SP3 
Mac OS X: 10.9 or above

iOS 7.0 or later


Control Modes Underslung Mode
Upright Mode
Briefcase Mode
Supported Camera Dimensions Maximum depth at center of mass on camera base plate: 4.7" / 120 mm
Maximum height measured from top of camera base plate: 7.7" / 195 mm
Maximum width: 6.3" / 160 mm
Power Requirements 4S Ronin-M Battery
Operating Temperature -5 to 122°F / -15 to 50°C
Dimensions (W x D x H) 19.7 x 8.3 x 16.5" / 500 x 210 x 420 mm
Weight 5.07 lb / 2.3 kg (fully loaded with handlebar)

1x Ronin-M

1x Ronin-M Transmitter (Controller)

2x Intelligent Battery for Ronin-M (1580mAh)

1x Battery Charger

1x Tuning Stand

1x Camera Mounting Plate

2x Camera Screw A (1/4"-20)

2x Camera Screw B (3/8"-16)

2x Camera Screw C (1/4"-20)

2x Camera Screw D (3/8"-16)

2x Allen Wrenches

Write Your Own Review

You're reviewing: (sold)Pre-owned DJI Ronin-M Kit